Lighthouse 2 (LH2) calibration#

Lighthouse 2 gives every DotBot a real-world (x, y) position on your arena floor. Two SteamVR base stations sweep the room with IR; each DotBot’s LH2 sensor times the sweeps. Calibration is the one-time step that maps those raw sweep counts to metric coordinates: you place one DotBot on four known corners of a square, capture, and the resulting transform is pushed to the whole fleet.

You do this once per physical setup (move a base station -> recalibrate).

The default flow is over the air - drive one already-deployed DotBot through the corners over the swarm, no cable and no firmware swap. If you’d rather calibrate a single DotBot on the bench over USB, see LH2 calibration over a cable.

Prerequisites#

A provisioned swarm: a gateway plus sandbox-host DotBots, reachable from your config (see swarm).
Two LH2 base stations mounted ~2 m up, facing the arena.
A square marked on the floor with a known side length.
The [calibrate] extra (the homography solve uses opencv):

pip install 'pydotbot[calibrate]'

Capture and push#

The calibration is a property of the arena (the base-station layout), not the individual DotBot, so you capture once from any one DotBot and apply the result to the whole fleet. Two steps:

dotbot swarm stop                                  # put the DotBots in READY
dotbot swarm lh2-calibration collect \
    --device BC3D3C8A2A6F8E68 -d 500               # capture from one DotBot -> solve -> save
dotbot swarm lh2-calibration push \
    ~/.dotbot/calibrations/calibration-<UTC>.toml  # apply to every ready DotBot

collect walks one DotBot through the four corners - top-left -> top-right -> bottom-left -> bottom-right - (capture only runs while the DotBot is in READY, so swarm stop first). Each prompt triggers a raw-count capture over the air; it then solves the homography and saves a calibration-<UTC>.toml under ~/.dotbot/ (the path is printed at the end). Find the --device address with dotbot swarm status.

push with no --device sends that calibration to every ready DotBot - the whole arena shares one transform. It accepts a calibration-*.toml or the legacy raw calibration.out payload; the format is picked by file extension.

Note

collect --push is a single-DotBot shortcut: it sends the result to only the --device DotBot you captured from (handy to spot-check that one DotBot, or for a single-DotBot setup). To calibrate the fleet, run the standalone push above - it targets all ready DotBots.

Once pushed, the DotBots report positions, which show up live in the controller Web UI.

`collect` flags#

Flag	Default	Meaning
`--device`	(required)	DotBot link-layer address in hex (from `dotbot swarm status`).
`-d`, `--distance`	calibration default	Square side length, in mm (see sizing below).
`-n`, `--conn` / `-s`, `--swarm-id`	from config	Swarm connection, like the other `dotbot swarm` commands.
`--timeout`	`5` s	Seconds to wait for each capture before re-triggering.
`--retries`	`3`	Re-trigger this many times per corner before giving up.
`--tag`	-	Arena/setup label (e.g. `office-2x2m`) added to the filename + metadata.
`--push`	off	After solving, send to the captured `--device` DotBot only (use the standalone `push` for the whole fleet).

See dotbot swarm lh2-calibration collect --help for the full list.

Sizing `-d`#

-d is the side of your reference square, in millimeters. The usable arena is 5× the square side, with the square centered (a 2·d margin on every side):

 ←─────────────── 5·d ────────────→
┌──────────────────────────────────┐  ↑
│                                  │  │
│                                  │  │
│           ←─── d ───→            │  │
│       TL  ●─────────●  TR        │  │
│           │         │            │ 5·d
│           │         │            │  │
│       BL  ●─────────●  BR        │  │
│                                  │  │
│←── 2·d ──→                       │  │
└──────────────────────────────────┘  ↓

                  ⌖ LH2 base station (mounted ~2 m up, facing the arena)

TL/TR/BL/BR are the four reference points you place the DotBot on; d is the square side (--distance, in mm), 5·d the resulting arena.

`-d`	Square	Usable arena
`400`	40 cm	2.0 m × 2.0 m
`500`	50 cm	2.5 m × 2.5 m
`800`	80 cm	4.0 m × 4.0 m (used for the 725-DotBot Limerick run)

Troubleshooting#

Capture times out - the DotBot isn’t in READY (run dotbot swarm stop first), or it can’t see both base stations. The address passed to --device must match one from dotbot swarm status.
Positions look skewed or mirrored - the corners were captured out of order. Re-run collect and follow TL -> TR -> BL -> BR exactly.
Positions are scaled wrong - -d didn’t match the real square. It’s in millimeters, not centimeters.